HT-IQT-B Piezoresistive Silicon Pressure Sensor
Introduction of diffused silicon pressure sensor:
HT - IQT - B silicon pressure sensor is a kind of embedded
diaphragm.Pressure was transferred to the sensitive chip through a
stainless steel diaphragm and sealed silicone oil. The sensor chip
converts the pressure into a detectable millivolt electrical
signal. Thus, we can intuitively observe the pressure value of the
measured medium. This product adopts plate diaphragm structure,
with high temperature heat sink, high temperature medium
measurement effect is good. The bare flat diaphragm is easy to
clean and has a good effect on the measurement of viscous
media.Apply to food, health and other industries.
Product Features of diffused silicon pressure sensor:- 316L stainless steel housing packaging.
- Temperature compensation and zero point correction through thick
film.
- High-temperature flush diaphragm structure for easy cleaning.
Applications of diffused silicon pressure sensor:- Suitable for measuring non-corrosive gas and liquid pressure with
316L stainless steel compatibility.
- Food and beverage industry.
- Industrial process control.
Electrical performance of diffused silicon pressure sensor:- Power Supply: ≤2mA DC (0.4-1.5mA DC).
- Input Impedance : 2.5KΩ~6KΩ.
- Output Impedance: 2.5KΩ~6KΩ.
- Electrical Connection: Gold-plated Kovar pins or 100mm
high-temperature wires.
| Performance Parameters of diffused silicon pressure sensor: |
| Measurement Range | Gauge(G) | 35KPa,100KPa,200KPa,350KPa,1000KPa,2000Kpa |
| Absolute(A) | 100KPaA,200KPaA,350KPaA,700KPaA,1000KPaA,2000KPaA |
| Sealed(S) | 3500KPaS |
| Typ | Max | Unit |
| NonLinearity | ±0.15 | ±0.3 | %F.S |
| Repeatability | 0.05 | 0.1 | %F.S |
| Hysteresis | 0.05 | 0.1 | %F.S |
| Zero Offset Output | 0±1 | 0±2 | mV |
| Full Scale Output | ≤20KPa | 50±10 | 50±30 | mV |
| ≥35kPa | 100±10 | 100±30 | mV |
| Zero Offset Temp. Drift | ≤20KPa | ±1 | ±2 | %F.S |
| ≥35kPa | ±0.5 | ±1 | %F.S |
| Full Scale Temp. Drift | ≤20KPa | ±1 | ±2 | %F.S |
| ≥35kPa | ±0.5 | ±1 | %F.S |
| Compensated Temp. | ≤20KPa | 0~50 | ºC |
| ≥35kPa | 0~70 | ºC |
| Operating Temperature | -20~80 | ºC |
| Storage Temperature | -40~125 | ºC |
| Allowable Overload | Take the smaller value between 3 times the full scale or 120MPa | |
| Burst Pressure | 5X the full scale | |
| Long-term Stability | 0.2 % | F.S/Year |
| Diaphragm Material | 316L | |
| Insulation Resistance | ≥200MΩ 100VDC | |
| Shock | 100g,11ms | |
| Response Time | ≤1ms | |
| O-ring Seal | Nitrile rubber or Fluoro rubber | |
| Filling Medium | Silicon Oil | |
| Weight | ~220g | |
| The parameters are tested under the following conditions: 1.5mA
@25°C |
| Outline Construction |
| Dimension | 
|
| Electrical connection and compensation |
|
1. Pay attention to the fit between the core size and the
transmitter housing during assembly to achieve the
required airtightness
2. During the assembly of the housing, ensure it is aligned
vertically and apply even pressure to avoid jamming or damaging the
compensation plate.
3. If the measured medium is not compatible with the core diaphragm
and the housing material (316L), special instructions should be
provided when placing the order.
4. Avoid pressing the sensor diaphragm with hands or sharp objects
to prevent damage to the core due to diaphragm deformation or
piercing.
5. Keep the pressure port of the gauge pressure core open to the
atmosphere and prevent the entry of water, water vapor, or
corrosive media into the core negative pressure chamber.
6. If there are any changes to the pin leads, follow the label on
the actual core for reference.
1.Q: What are the features of your pressure sensor transmitters?
A: High precision, durability, and excellent performance.
Customization available.2.Q: Can I customize special specifications?
A: Yes, our engineers can tailor products to meet specific needs. We provide OEM and ODM service3.Q: What is your production capacity?
A: Our manufacturing facilities can produce up to 30,000 pressure
sensor transmitters per month, so we are fully capable of meeting
the needs of large-scale orders. However, it is advisable to
contact our sales team in advance to ensure smooth production and
delivery scheduling
.4.Q: What's the typical delivery period?
A: 5~8 working day for standard models. Customized products may
vary.5.Q: How are the products priced? Any discounts?
A: Competitive pricing with discounts for bulk orders or long-term
partners
.6.Q: What is the warranty of your products? And after-sales
service?
A: Our warranty time is 24 months after shipment, and our
after-sales will respond with your questions in 24hrs, remote
instruction by PC network is always available.
